Radio Code Start Pack Box III

Complete solutions for unlocking car radios and navigations.

Buying this set you save 405 euro and you will get complet of cables for free.

Complex set for car radios and navigations service with Martech Box III based on STM32 cpu, which supports adequate speed and stability.

Actual full package consist of:

Box III supports communication over:

JTAG (np. LCN, RNS310, LSRNS, HSRNS, HSMCA)
OBD2 (OBD (K-Line, ALDL, OBD-I, OBD-1.5, OBD-II, EOBD, EoBD2, JOBD, ADR, SAE J1850 PWM, SAE J1850 VPW, ISO 9142-2)
UART (RS232, TX232, RNS510)
CAN L, CAN H, K-Line, L-Line, ADC-A, ADC-B
K-line level 1..15V (without external power supply, just from USB to 9V)
L-line level 1..15V (without external power supply, just from USB to 9V)
RS232 TX/RX in -9..+9V range
RX/TX outputs 1..5V (USB)
MBUS on TX output
MBUS na RX output
on universal outputs
MAUS BUS (for cancheck in BP radios)

New functions in Programmer bookmark:

Eeprom / Flash: serial spi, i2c (X24c00 also), microwire (rotated with auto pin finding), 77007MN, KKZ
NEC (more types, faster connection)
Motorola (new bootloaders for HC05/11, secured also)
ST92 (more stable of work, reading secured in future)
Renesas M16/M32 (possibility to read out some of secured versions)
JTAG - Box III as a JTAG programmer for many type of ARM 7/9
no file coding – all can be saved in pure binary file (.mbin file is supported too)
a possibility of setting Vreg voltage, Rise Time, IREG , reading speed

Box III specifications:

diagnostic DB25 connector (inputs, outputs, TX232, RX232, CAN L, CAN H, K-Line, L-Line, Vreg, ADC-A, ADC-B)
USB connector
9V external power supply connector
4 led diodes (BUSY/ERROR, CONNECTION, RX, TX)
firmware update on the fly (in background, changes came after software close)
drivers installations directly from windows update xp/vista/win7/win8/win8.1
autologin to support Forum Forum
software, drivers installation can be find on Help online
12 months of warranty
12 months free support for activations purchased

What's new in Box III, which is not on Clip so far:

full support (read, write, erase) of M35080 3/6/V6/VP/D80/D160 (under the tab of programmer)
new user interface - easier and faster selection of models, more features
read / erase / write Serial SPI memories likeMX25L160 , W25X32 and F-RAM eg. FM25L04
RNS 315 original code reading the without the use of expander (procedures work independently without control computer)
JTAG programmer (in development)
in many cases, support K / L - Line without external power supply 12V
K / L support in different voltage ranges from 1 to 15 V (programmable)
10 universal I / O lines with programmable logic from 1 to 5 V
UART and RS232 (separate outputs for RS232 - a standard PC or signal level from -9V ..+ 9V )
UART in logic from 0 to 15V - max voltage from 1V to 15V
RS232 with the range of -12V .. +12V
work on USB power + the ability to work on external power
possibility to supply external circuits from the box
Vreg - programmable voltage from 0.5 .. 5V (max voltage dependent on the performance of the computer USB)
hardware and software support for most protocols OBD ( ALDL , OBD -I, OBD -1.5 , OBD-II , EOBD , EoBD2 , JOBD , ADR , SAE J1850 PWM , SAE J1850 VPW , ISO 9142-2)
device is fully expandable, on the request of customers also
programmable current protection outputs, IREG (sum of all outputs IO1 .. I08 + RX + TX)
analog inputs - ADC-A, ADC-B

Run software in demo mode to see supported models and functions.